Chemicals/Coatings

Showing 1 - 12 of 42 results
Ameripolish - 3DSP Stain Protector
$65.00
STAIN PROTECTOR Ameripolish® 3D SP is a breathable semi-penetrating/semitopical sealer that helps to protect surfaces against stains and etching. 3D SP creates a water-resistant barrier that prevents liquids from infiltrating the surface, protecting against staining and color dispersion. Ready to use (RTU). UV stabilizers help protect against fading. Creates water-resistant barrier to prevent staining, etching, and protect color. 3D SP is a color enhancer for polish concrete floors with dye. Contains 3D densifier properties to aid in hardening and dust-proofing. COST PERFORMANCE 2-3¢ PER FT2 2,000-2,500FT2 PER GALLON Safety Data Sheet Technical Data Sheet
STAIN PROTECTOR Ameripolish® 3D SP is a breathable semi-penetrating/semitopical sealer that helps to protect surfaces against stains and etching. 3D...
APF - OIL STOP PRIMER 1.25Gal Kit
$87.99
  Oil Stop Primer is a low viscosity, 100% solids resin designed for use as a primer on concreteslabs that are contaminated with hydrocarbons, such as motor oil, solvents, cutting oils andhydraulics fluids.    Oil Stop Primer - Datasheet  Oil Stop Primer - Part A - SDS  Oil Stop Primer - Part B - SDS
  Oil Stop Primer is a low viscosity, 100% solids resin designed for use as a primer on concreteslabs that...
Hi Tech - Spall TX3
$200.00
Spall TX3 is a rapid set, high strength low viscosity polyurethane repair material. This two component, 1:1 system is designed to repair damaged joints, cracks, spalls and other concrete surface defects. Spall TX3 has additional working time when compared to TX, which makes it well suited as a pre polish filler. Spall TX3 can be hand mixed and troweled across concrete floors suffering from pinholes, pop outs and other defects. It can also be mixed with sand and cement to create a repair mortar material. Spall TX3 is low viscosity, 100% solids and VOC free. Download Color Chart Spall TX3 TDS Spall TX3 SDS Part A Spall TX3 SDS Part B
Spall TX3 is a rapid set, high strength low viscosity polyurethane repair material. This two component, 1:1 system is designed to...
Hi Tech - Spall FX
$47.00
Spall FX is a rapid set, high strength low viscosity polyurethane repair material. This two component, 1:1 system is designed to repair damaged joints, cracks, spalls and other concrete surface defects. Spall FX cures in about 15 minutes and can be ground and polished immediately. Download Color Chart Spall FX TDS Spall FX SDS Part A Spall FX SDS Part B
Spall FX is a rapid set, high strength low viscosity polyurethane repair material. This two component, 1:1 system is designed to...
CONGELZ WASTE WATER HARDENER - 40lbs
$200.00
Congelz Waste Water Hardener (BOM #107069) is the perfect method to dispose of unwanted rinse water from any cement or concrete project. Congelz patented technology is great for mortars, stuccos, grouts, patching products, and other similar materials. Using Congelz solves the issues caused by cementitious waste disposal - no more clogged drains or dumping of product on job sites. Simply add the product to your rinse water, allow to harden, and toss the works in the trash! Environmentally safe! Passes EPA 9095.   Printable Info TDS - Congelz SDS - Congelz FAQ - Congelz
Congelz Waste Water Hardener (BOM #107069) is the perfect method to dispose of unwanted rinse water from any cement or...
Vexcon - STARSEAL PS CLEAR - 5GAL
$160.02 $177.80
StarSeal PS Clear STARSEAL PS CLEAR enhances the natural beauty of gray and decorative concrete surfaces and produces a wear-pattern free, shine retentive permanently sealed, low-maintenance densified concrete floor. StarSeal PS Clear is a high solids potassium based silicate that rapidly penetrates without scrubbing and rinsing. Simply apply, re-distribute and re-apply until the concrete no longer absorbs the material. Once absorbed, StarSeal PS Clear reacts with the calcium hydroxide in the concrete producing a stronger more durable, dust free, superior looking and performing long lasting concrete floor. BENEFITS Long lasting and extremely durable High solids forumation No scrubbing or rinsing required Eliminates or reduces waste stream during installation Odorless, non-hazardous, USDA approved Easy to clean LEED points Abrasion, wear resistant No topical film to wear through Performance warranty Low maintenance. No waxing or resurfacing required Brochure StarSeal PS Clear Safety Data Sheet StarSeal PS Clear
StarSeal PS Clear STARSEAL PS CLEAR enhances the natural beauty of gray and decorative concrete surfaces and produces a wear-pattern...
APF - VaporSolve  Primer Clear Moisture Remediation Coating
$46.57
VaporSolve Primer is a specially formulated water-based epoxy designed to provide superior adhesion over concrete with high levels of moisture vapor emissions. When used with the companion finish coat, 100% solids VaporSolve 100, a coating system is achieved that reduces moisture vapor emissions to acceptable levels for all flooring and maintains its bond under continuously moist, alkaline conditions. VaporSolve Primer is also ideal over damp or green concrete. The product may be applied at temperatures between 40-100F. VaporSolve Primer is based on epoxy curing agent technology with more than 30 years of success as a concrete primer. It has been formulated with very low viscosity and surface tension to ensure excellent substrate wetting, penetration and adhesion. Laboratory testing has shown that VaporSolve Primer penetrates 25-30% deeper into concrete than low viscosity (250 cps) 100% solids epoxy. This exceptional penetration and adhesion gives VaporSolve Primer a distinct advantage over 100% solids...
VaporSolve Primer is a specially formulated water-based epoxy designed to provide superior adhesion over concrete with high levels of moisture...
APF - VaporSolve 100 Clear Moisture Barrier Coating
$72.47
VaporSolve 100 is a specially formulated 100% solids epoxy coating designed for use over concrete with high moisture levels for the purpose of isolating the concrete from moisture sensitive flooring. When used without a primer in a single application, it is referred to as the VaporSolve Basic System. This system should only be used over concrete that has never been treated with reactive silicate curing compounds or densifiers. VaporSolve 100 has been formulated with low viscosity and excellent substrate wetting capabilities to promote penetration and adhesion. The special hydrophobic curing agent allows for adhesion to damp or wet concrete. This product will cure fully even when applied underwater. In addition, VaporSolve 100 is based on Bisphenol F epoxy which gives the material enhanced chemical crosslinking over products based on standard Bisphenol A epoxy. More crosslinking helps to reduce the coatings moisture permeability and increases its long-term resistance to water and...
VaporSolve 100 is a specially formulated 100% solids epoxy coating designed for use over concrete with high moisture levels for...
APF - VaporSolve™ 100 Clear Moisture Barrier Coating
$72.47
VaporSolve™ 100 is a specially formulated 100% solids epoxy coating designed for use over concrete with high moisture levels for the purpose of isolating the concrete from moisture sensitive flooring. When used without a primer in a single application, it is referred to as the VaporSolve™ Basic System. This system should only be used over concrete that has never been treated with reactive silicate curing compounds or densifiers. VaporSolve™100 has been formulated with low viscosity and excellent substrate wetting capabilities to promote penetration and adhesion. The special hydrophobic curing agent allows for adhesion to damp or wet concrete. This product will cure fully even when applied underwater. In addition, VaporSolve™ 100 is based on Bisphenol F epoxy which gives the material enhanced chemical crosslinking over products based on standard Bisphenol A epoxy. More crosslinking helps to reduce the coating’s moisture permeability and increases its long-term resistance to water and alkalinity....
VaporSolve™ 100 is a specially formulated 100% solids epoxy coating designed for use over concrete with high moisture levels for...
APF - VaporSolve™ Primer Clear Moisture Remediation Coating
$46.57
VaporSolve™ Primer is a specially formulated water-based epoxy designed to provide superior adhesion over concrete with high levels of moisture vapor emissions. When used with the companion finish coat, 100% solids VaporSolve™ 100, a coating system is achieved that reduces moisture vapor emissions to acceptable levels for all flooring and maintains its bond under continuously moist, alkaline conditions. VaporSolve™ Primer is also ideal over damp or green concrete. The product may be applied at temperatures between 40-100 °F. VaporSolve™ Primer is based on epoxy curing agent technology with more than 30 years of success as a concrete primer. It has been formulated with very low viscosity and surface tension to ensure excellent substrate wetting, penetration and adhesion. Laboratory testing has shown that VaporSolve™ Primer penetrates 25-30% deeper into concrete than low viscosity (250 cps) 100% solids epoxy. This exceptional penetration and adhesion gives VaporSolve™ Primer a distinct advantage over 100%...
VaporSolve™ Primer is a specially formulated water-based epoxy designed to provide superior adhesion over concrete with high levels of moisture...
APF - Polyurea 5100
$136.63
Polyurea 5100 is a 100% solids, two-component, aliphatic polyurea/polyaspartic hybrid.  A unique resin chemistry has provided the raw materials to formulate this coating, which offers the desirable properties of polyester-polyurethane materials with virtually no odor and fewer film thickness limitations.   Polyurea 5100 is a low-viscosity, solvent-free, easy-to-handle product that provides a very high gloss finishes that are both hard and abrasion resistant. This material releases soil easily and has excellent resistance to a broad range of chemicals.   Unlike conventional polyurea materials, Polyurea 5100 has enough work time to be applied by brush and roller. It is available in both a regular cure and a fast-cure version for use in rapid turnaround projects. The fast-cure material may be used at temperatures as low as 20F. For exterior applications, a UV stabilizer package is incorporated to ensure long-term gloss retention and resistance to yellowing.   Polyurea 5100 was developed as...
Polyurea 5100 is a 100% solids, two-component, aliphatic polyurea/polyaspartic hybrid.  A unique resin chemistry has provided the raw materials to...
APF - Polyurea 5001
$122.67

                Bone
                
                Flaxen
                
                Wheat
                
                Sand
                
                Buff
                
                Thatch Brown
                
                Adobe
                
                RED BRICK
                
                Seattle Red
                
                Concrete Gray
                
                Delta Fog
                
                Sterling
                
                Slate
                
                Safety Yellow
                
                Safety Red
                
                Safety Blue
Polyurea 5001 is a two component, ultra high solids, aliphatic polyurea/polyaspartic hybrid. It is a pigmented material capable of obtaining excellent adhesion to dry, properly prepared concrete. Polyurea 5001 is a low viscosity, easy to handle product that gives very high gloss finishes that are both hard and abrasion resistant. The material releases soils easily and has excellent resistance to a broad range of chemicals. It is a very fast curing material and may be used at temperatures as low as 20F, making it ideal for use in cold weather or rapid turnaround projects.   Polyurea 5001 was developed as a fast cure primer and finish coat for various protective coating and seamless flooring applications. Its use as a primer and base coat in color chip flooring allows for the application to be completed in one day, even at lower temperatures. As a fast curing high performance finish coat, typical...
Polyurea 5001 is a two component, ultra high solids, aliphatic polyurea/polyaspartic hybrid. It is a pigmented material capable of obtaining...
APF - Polyurea 5000
$162.41
Polyurea 5000 is a two-component, ultra high solids, aliphatic polyurea/polyaspartic hybrid. New, unique resin chemistry has provided the raw materials to formulate this coating, which gives it the desirable properties of polyester-polyurethane materials with greatly reduced odor and less film thickness limitations.   Polyurea 5000 is a low viscosity, easy-to-handle product with a very high gloss finish. Its also hard and abrasion resistant. This material releases soils easily and has excellent resistance to a broad range of chemicals. Unlike conventional polyurea materials, Polyurea 5000 has enough work time to be applied by brush and roller.   Polyurea 5000 is available in both a regular cure and a fast cure (FC) for use in rapid turnaround projects. Polyurea 5000 FC can handle vehicle traffic 24 to 48 hours after application, depending on the temperature. It is also available with a UV absorber package, which should be purchased separately and added to...
Polyurea 5000 is a two-component, ultra high solids, aliphatic polyurea/polyaspartic hybrid. New, unique resin chemistry has provided the raw materials...
APF - Polyaspartic 7500
$101.44
Polyaspartic 7500 is a two-component, high solids, aliphatic polyaspartic. This unique resin chemistry has the desirable properties of polyester-polyurethane materials, yet has a faster cure time and fewer film thickness limitations. It was developed as a high-performance coating for various protective coatings and seamless flooring applications.   Unlike conventional polyurea materials, Polyaspartic 7500 has enough work time to be applied by brush and roller, making it ideal for projects with a quick turnaround requiring abrasion/chemical resistance. For exterior applications, a UV stabilizer package is included, ensuring long-term gloss retention and resistance to yellowing.   A low-VOC version of Polyaspartic 7500 is available with VOC content of less than 100 grams per liter.   The Polyaspartic 7500 Advantage   Rapid curing; return to full service in 24 hours Hard finish and abrasion resistant Excellent resistance to a broad range of chemicals Very high gloss finish Low viscosity, easy-to-handle product Material easily...
Polyaspartic 7500 is a two-component, high solids, aliphatic polyaspartic. This unique resin chemistry has the desirable properties of polyester-polyurethane materials,...
APF - Epoxy 400 Thixotropic
$90.67

                Clear
                
                Bone
                
                Flaxen
                
                Wheat
                
                Sand
                
                Buff
                
                Thatch Brown
                
                Adobe
                
                Red Brick
                
                Seattle Red
                
                Concrete Gray
                
                Delta Fog
                
                Sterling
                
                Slate
                
                Safety Yellow
                
                Safety Red
                
                Safety Blue
Epoxy 400 is a low viscosity, 100% solids resin system used in a variety of flooring applications including high build coatings, aggregate-filled flooring and decorative epoxy pebble applications. This material cures blush-free and provides an outstanding balance of physical strength, flexibility and chemical resistance.   Epoxy 400 has excellent clarity for use over color quartz aggregate and decorative architectural concrete. The pigmented material features high pigment loading for good substrate hide and color consistency when roller applied. Epoxy 400 has considerably lower viscosity than most competitive products providing improved handling at cooler temperatures and exceptional troweling characteristics. The lower viscosity allows for the addition of fine silica fillers for easy application of slurry type floors. A fast cure hardener is available when cold weather curing, (down to 40F), or accelerated room temperature curing is required. A special hardener is available when adhesion to damp concrete is required.   The versatility of...
Epoxy 400 is a low viscosity, 100% solids resin system used in a variety of flooring applications including high build...
APF - Epoxy 400
$90.67

                Clear
                
                Bone
                
                Flaxen
                
                Wheat
                
                Sand
                
                Buff
                
                Thatch Brown
                
                Adobe
                
                Red Brick
                
                Seattle Red
                
                Concrete Gray
                
                Delta Fog
                
                Sterling
                
                Slate
                
                Safety Yellow
                
                Safety Red
                
                Safety Blue
Epoxy 400 is a low viscosity, 100% solids resin system used in a variety of flooring applications including high build coatings, aggregate-filled flooring and decorative epoxy pebble applications. This material cures blush-free and provides an outstanding balance of physical strength, flexibility and chemical resistance.   Epoxy 400 has excellent clarity for use over color quartz aggregate and decorative architectural concrete. The pigmented material features high pigment loading for good substrate hide and color consistency when roller applied. Epoxy 400 has considerably lower viscosity than most competitive products providing improved handling at cooler temperatures and exceptional troweling characteristics. The lower viscosity allows for the addition of fine silica fillers for easy application of slurry type floors. A fast cure hardener is available when cold weather curing, (down to 40F), or accelerated room temperature curing is required. A special hardener is available when adhesion to damp concrete is required.   The versatility...
Epoxy 400 is a low viscosity, 100% solids resin system used in a variety of flooring applications including high build...
APF - Epoxy 300 Flex
$60.61

                Clear
                
                White
                
                Concrete Gray
                
                Sterling
                
                Slate
                
                Buff
Epoxy 300 Flex is a 100% solids, medium viscosity, flexible epoxy system. It has excellent elongation, hardness and impact resistance. The material cures, blush-free, and forms a tenacious bond to damp concrete and properly prepared metal.   It can be purchased in a thickened paste version for easy joint and crack filling. A special hardener is available where cold weather curing (down to 40 degrees), or accelerated room temperature cure is required.   Epoxy 300 Flex was developed for industrial joint and crack repair. It's combination of resilience and physical strength allows it to absorb the impact of heavy loads and steel wheeled traffic. When used as a coating system, it is especially well suited for applications where surface movement, vibrations or thermal cycling may defeat the protection of a rigid material. Typical applications of this type would include wood decks, suspended concrete slabs, mechanical rooms and exterior aggregate-filled flooring....
Epoxy 300 Flex is a 100% solids, medium viscosity, flexible epoxy system. It has excellent elongation, hardness and impact resistance....
APF - Epoxy 200
$91.49

                Clear/No Color
                
                Bone
                
                Flaxen
                
                Wheat
                
                Sand
                
                Buff
                
                Thatch Brown
                
                Adobe
                
                Red Brick
                
                Seattle Red
                
                Concrete Gray
                
                Delta Fog
                
                Sterling
                
                Slate
                
                Safety Yellow
                
                Safety Red
                
                Safety Blue
Epoxy 200 is a two component water-based epoxy with excellent adhesion and rapid cure times. Its unique chemistry provides short re-coat times and good low temperature curing. This material has little odor, applies easily and adheres to damp concrete.   Epoxy 200 was designed for use as a fast curing primer under epoxy, acrylic, polyurethane and polyurea materials. It may also be used as a base coat in fast turnaround color chip systems. Re-coat times range from 30 minutes to 90 minutes depending on film thickness, curing conditions and the type of top coat used.   Epoxy 200 is ideally suited as a primer over properly neutralized interior acid stains where odor cannot be tolerated. Epoxy 200 primer with Polyurethane 100 or Polyurethane 501 top coats may be accomplished in one trip to the job site. Fewer trips to the job site result in reduction of labor costs.   Colors...
Epoxy 200 is a two component water-based epoxy with excellent adhesion and rapid cure times. Its unique chemistry provides short...
APF - Epoxy 100
$61.86

                Clear/No Color
                
                Bone
                
                Flaxen
                
                Wheat
                
                Sand
                
                Buff
                
                Thatch Brown
                
                Adobe
                
                Red Brick
                
                Seattle Red
                
                Concrete Gray
                
                Delta Fog
                
                Sterling
                
                Slate
                
                Safety Yellow
                
                Safety Red
                
                Safety Blue
Epoxy 100 is a two component water-based epoxy system that features ease of application, very low odor and excellent overall coating performance.åÊ This material cures blush free over a wide range of temperatures and adheres tenaciously to a variety of substrates including damp or wet concrete. Because of its affinity for moisture and inherent alkalinity resistance, Epoxy 100 may be used over green concrete with proper surface preparation.   Epoxy 100 is used as a general purpose coating for concrete floors and as a primer under epoxy, polyurethane and acrylic materials. The raw material package has a 30 year history of success as a concrete coating. Epoxy 100 is recommended for coating warehouse and factory floors, automotive repair facilities, residential garage floors and many other commercial and industrial maintenance applications.   Colors & Finishes Clear All 16 Standard Colors   Kit Sizes   1.25 Gallons 5 Gallons  Epoxy 100 Data...
Epoxy 100 is a two component water-based epoxy system that features ease of application, very low odor and excellent overall...
APF - CEM-SEAL
$35.59

                Clear/No Color
                
                Bone
                
                Flaxen
                
                Wheat
                
                Sand
                
                Buff
                
                Thatch Brown
                
                Adobe
                
                Red Brick
                
                Seattle Red
                
                Concrete Gray
                
                Delta Fog
                
                Sterling
                
                Slate
                
                Safety Yellow
                
                Safety Red
                
                Safety Blue
APF Cem-Seal is a water-based acrylic emulsion used in a variety of decorative concrete applications. It is available in both clear and pigmented formulations, dries quickly, and is high in solids for single component emulsion type materials. Cem-Seal forms hard coating films, resists blushing, and provides excellent resistance to yellowing in exterior applications.  Pigmented Cem-Seal is used as a color coat over polymer concrete and spray applied decking. Clear Cem-Seal was designed as a fast drying build coat in color chip flooring and as an economical sealer over polymer concrete in light duty applications. It is an excellent primer on polymer concrete when two component polyurethane or polyurea/ polyaspartics are used as finish coats.   Colors & Finishes Clear All 16 Standard Colors     Kit Sizes   1 Gallons 5 Gallons APF Cem-Seal Data Sheet APF Cem-Seal SDS APF Cem-Seal Pigmented SDS Standard Color Chart
APF Cem-Seal is a water-based acrylic emulsion used in a variety of decorative concrete applications. It is available in both...
APF - Acryseal
$34.66
APF Acryseal is a clear, solvent-based acrylic designed for sealing conventional concrete, exposed aggregate, porous tile, concrete pavers and a variety of architectural concrete surfaces. Acryseal is based on a hard acrylic polymer that produces coatings that give good gloss, stain-resistance and cleanability. Adhesion to properly prepared cementitious surfaces is excellent, and the material is completely non-yellowing.   Acryseal is produced in a standard formulation that brings out the rich, natural beauty of the substrate.   Colors & Finishes Gloss   Kit Sizes 1 Gallon 5 Gallons 55 Gallons APF Acryseal AZ 25% SDS APF Acryseal Data Sheet APF Acryseal Satin AZ 25% SDS
APF Acryseal is a clear, solvent-based acrylic designed for sealing conventional concrete, exposed aggregate, porous tile, concrete pavers and a...
APF - Acryseal VOC
$51.20
APF Acryseal is a clear, solvent-based acrylic designed for sealing conventional concrete, exposed aggregate, porous tile, concrete pavers and a variety of architectural concrete surfaces. Acryseal is based on a hard acrylic polymer that produces coatings that give good gloss, stain-resistance and clean-ability.  Adhesion to properly prepared cementitious surfaces is excellent, and the material is completely non-yellowing.   Acryseal is produced in a standard formulation that bring out the rich, natural beauty of the substrate.   Colors & Finishes Clear Satin Finish Gloss   Kit Sizes 1 Gallon 5 Gallons 55 Gallons APF Acryseal CA 22% SDS APF Acryseal CA 25% SDS APF Acryseal Satin CA 25% SDS APF Acryseal VOC Data Sheet
APF Acryseal is a clear, solvent-based acrylic designed for sealing conventional concrete, exposed aggregate, porous tile, concrete pavers and a...
APF - Polyurethane 501
$137.19

                Clear/No Color
                
                Bone
                
                Flaxen
                
                Wheat
                
                Sand
                
                Buff
                
                Thatch Brown
                
                Adobe
                
                Red Brick
                
                Seattle Red
                
                Concrete Gray
                
                Delta Fog
                
                Sterling
                
                Slate
                
                Safety Yellow
                
                Safety Red
                
                Safety Blue
Polyurethane 501 is a high solids, two component, water-based aliphatic polyurethane. This unique material provides performance properties equal to conventional solvent-based catalyzed urethanes without the associated health and environmental problems. It offers substantial performance improvements over first generation catalyzed water-based polyurethanes, including higher film build capabilities, improved chemical resistance and resistance to hot tire staining.   Polyurethane 501 gives hard, durable coatings that feature good gloss, easy cleanability and superior abrasion resistance. Resistance to yellowing from U.V. light is excellent. For exterior desert applications, a special U.V. absorber package can be incorporated to ensure long-term chalk resistance and gloss retention.   Polyurethane 501 has been developed as a high performance finish coat for various seamless flooring,coating, and architectural concrete applications where odor cannot be tolerated. It is the ideal top coat for areas that require maximum gloss retention, ease of cleaning, and resistance to heavy foot traffic. Typical areas of...
Polyurethane 501 is a high solids, two component, water-based aliphatic polyurethane. This unique material provides performance properties equal to conventional...
APF - Polyurethane 325
$158.30

                Clear/No Color
                
                Bone
                
                Flaxen
                
                Wheat
                
                Sand
                
                Buff
                
                Thatch Brown
                
                Adobe
                
                Red Brick
                
                Seattle Red
                
                Concrete Gray
                
                Delta Fog
                
                Sterling
                
                Slate
                
                Safety Yellow
                
                Safety Red
                
                Safety Blue
Polyurethane 325 is a three component, high solids aliphatic moisture urethane. This product offers a remarkable combination of performance properties not found in other polymer coatings. Polyurethane 325 produces protective films which are hard, flexible and very impact resistant. These coatings feature extreme abrasion and scratch resistance, easy soil release and excellent resistance to a broad range of chemicals. For exterior applications, a UV stabilizer package is incorporated to insure long term chalk resistance and gloss retention.   Polyurethane 325 has been designed as a high performance top coat in various protective coating and seamless flooring applications. It provides maximum clean-ability and stain resistance when used as a finish coat in color chip flooring or epoxy-quartz flooring. This coating is ideally suited for clean-room floors, automotive repair facilities, aircraft hangars and other high wear areas requiring resistance to fuels and chemicals.   Colors & Finishes Clear Satin Finish All 16...
Polyurethane 325 is a three component, high solids aliphatic moisture urethane. This product offers a remarkable combination of performance properties...
APF - Polyurethane 250 VOC
$113.97
Polyurethane 250 is a two component, low viscosity acrylic urethane. It is used as a primer/sealer over a variety of surfaces. The use of special solvents and adhesion promoters gives this material excellent penetration and adhesion to minimally profiled concrete. Polyurethane 250 is U.V. stable for use in exterior applications, cures rapidly and is easily recoated with both solvent-based and water-based polyurethanes. When used as a finish coat, this material gives a hard, high gloss surface that offers excellent stain resistance and easy cleanability. Compared to solvent-based acrylic sealers, Polyurethane 250 offers substantial improvements in initial gloss, gloss retention and overall performance. Polyurethane 250 is available in a satin finish if a lower gloss is desired. A special version of this material is available to meet the 50 grams/liter VOC limit in California.Polyurethane 250 has been designed for use over concrete, acid stained surfaces, and various types of architectural concrete....
Polyurethane 250 is a two component, low viscosity acrylic urethane. It is used as a primer/sealer over a variety of...
APF - Polyurethane 250
$103.69
Polyurethane 250 is a two component, low viscosity acrylic urethane. It is used as a primer/sealer over a variety of surfaces. The use of special solvents and adhesion promoters gives this material excellent penetration and adhesion to minimally profiled concrete. Polyurethane 250 is U.V. stable for use in exterior applications, cures rapidly and is easily recoated with both solvent-based and water-based polyurethanes. When used as a finish coat, this material gives a hard, high gloss surface that offers excellent stain resistance and easy cleanability. Compared to solvent-based acrylic sealers, Polyurethane 250 offers substantial improvements in initial gloss, gloss retention and overall performance. Polyurethane 250 is available in a satin finish if a lower gloss is desired. A special version of this material is available to meet the 50 grams/liter VOC limit in California.Polyurethane 250 has been designed for use over concrete, acid stained surfaces, and various types of architectural concrete....
Polyurethane 250 is a two component, low viscosity acrylic urethane. It is used as a primer/sealer over a variety of...
APF - Polyurethane 100
$121.50

                Clear/No Color
                
                Bone
                
                Flaxen
                
                Wheat
                
                Sand
                
                Buff
                
                Thatch Brown
                
                Adobe
                
                Red Brick
                
                Seattle Red
                
                Concrete Gray
                
                Delta Fog
                
                Sterling
                
                Slate
                
                Safety Yellow
                
                Safety Red
                
                Safety Blue
Polyurethane 100 is a two component, high solids aliphatic polyurethane. This product offers a remarkable combination of performance properties not found in other polymer coatings. Polyurethane 100 produces protective films which are hard, flexible and very impact resistant. These coatings feature high abrasion and scratch resistance, exterior durability, easy soil release and excellent resistance to a broad range of chemicals. For exterior applications, a U.V. stabilizer package is incorporated to insure long term chalk resistance and gloss retention. A special accelerator is available when rapid project turnaround is required. Polyurethane 100 has been designed as a high performance top coat in various protective coating and seamless flooring applications. It provides maximum cleanability and stain resistance when used as a finish coat in color chip flooring or epoxy-quartz flooring. This coating is ideally suited for clean-room floors, automotive repair facilities, aircraft hangars and other high wear areas requiring resistance to fuels...
Polyurethane 100 is a two component, high solids aliphatic polyurethane. This product offers a remarkable combination of performance properties not...
APF - Polyurethane 100 VOC
$141.10

                Clear/No Color
                
                Bone
                
                Flaxen
                
                Wheat
                
                Sand
                
                Buff
                
                Thatch Brown
                
                Adobe
                
                Red Brick
                
                Seattle Red
                
                Concrete Gray
                
                Delta Fog
                
                Sterling
                
                Slate
                
                Safety Yellow
                
                Safety Red
                
                Safety Blue
Polyurethane 100 VOC is a two component, high solids aliphatic polyurethane formulated to be a lower VOC option to the standard Polyurethane 100. This product offers a remarkable combination of performance properties not found in other polymer coatings. Polyurethane 100 VOC produces protective films which are hard, flexible and very impact resistant. These coatings feature high abrasion and scratch resistance, exterior durability, easy soil release and excellent resistance to a broad range of chemicals. For exterior applications, a U.V. stabilizer package is incorporated to ensure long term chalk resistance and gloss retention. A special accelerator is available when rapid project turnaround is required.   Polyurethane 100 VOC has been designed as a high performance top coat in various protective coating and seamless flooring applications. It provides maximum cleanability and stain resistance when used as a finish coat in color chip flooring or epoxy-quartz flooring. This coating is ideally suited for...
Polyurethane 100 VOC is a two component, high solids aliphatic polyurethane formulated to be a lower VOC option to the...
Vexcon - Starseal Fusion WB 5Gal
$279.00 $310.00
StarSeal Fusion  Invisible Surface Repair Treatment   STARSEAL FUSION is an advanced concrete repair and restoration treatment for StarSeal PS or other silicate densifying floor treatments. StarSeal Fusion will repair small air holes, aggregate pop-outs, voids, micro cracks, small spider cracks and similar surface imperfections. While other types of repair materials become brittle and discolor the surface leaving it blotchy looking, StarSeal Fusion repairs and blends into the existing color of the concrete yielding a consistent natural looking floor. BENEFITS Fills holes, cracks with same color as concrete Makes repairs almost invisible Cures in 1 hour for additional grinding Increases gloss and clarity Yields a smoother, denser surface Compatible with all densifier, stain and dye systems Fills early grinding scratches Does not contain any pore clogging latex Will work with most epoxy terrazzo and all cementitious terrazzo
StarSeal Fusion  Invisible Surface Repair Treatment   STARSEAL FUSION is an advanced concrete repair and restoration treatment for StarSeal PS...
FlorockFloroSpartic Polyaspartic Systems - 2Gal Kit
$218.46
FloroSpartic Polyaspartic Systems FloroSpartic coatings are glossy, clear, aliphatic polyaspartics. These light stable, high performance polymeric systems can cure well even in cool conditions and provide outstanding chemical resistance to oil, grease and strong detergents. Ready for foot traffic in less than two hours at 70å¡F, the fast cure of FloroSpartic allows many flooring projects to be completed in a single day. åÊ FloroSpartic polyaspartic floor coatings are color-stable and non-yellowing, making them ideal for use in decorative systems incorporating various colored flakes, chips and aggregate blends. At the same time, they offer good tensile and flexural strength, lending FloroSpartic floors excellent resiliency under heavy use. They are a versatile and budget-friendly flooring solution for industrial, institutional and commercial locations, and furnish excellent life cycle value. All Florock Polymer Flooring meets USDA and FDA requirements. Optional FloroProof Moisture Vapor Transmission (MVT) Mitigation and FloroSeptic Antimicrobial properties are available. Colors Architectural...
FloroSpartic Polyaspartic Systems FloroSpartic coatings are glossy, clear, aliphatic polyaspartics. These light stable, high performance polymeric systems can cure well...
Florock Gloss Epoxy Floor Resin 4700 Kit - Clear -  4 gal
$264.00
Keep your floors looking fabulous with this high-grade floor resin 4700 kit designed by Florock.This is an excellent floor resin 4700 kit for concrete because of the epoxy resin and 100% solid base.The application temperature is 55 degrees to 90 degrees F. Dry-time is 6 hr. after application. A gloss finish is durable and looks great. It is designed for mild to moderate exposure conditions. It comes in clear, size 4 gal. TECHNICAL SPECS ItemFloor Resin 4700 Kit Base Type100% Solid Resin TypeEpoxy VOC ContentVOC Free Size4 gal. ColorGray FinishGloss Coverage100 sq. ft./gal. Dry Time Tack Free8 hr. Dry Time - Light Traffic12 hr. Dry Time12 hr. Dry Time Recoat12 to 48 hr. Application Temperature55 to 90 Degrees F Application MethodBrush, Roller, Spray SurfaceConcrete Exposure ConditionsMild to Moderate StandardsASTM C579, ASTM D2370 FeaturesIdeally Suited for Use As A Topcoat For Use WithMfr. No. M8-138QT, M1-067QT, M7-062QT, M4-056QT, M5-046QT, M5-045QT, M5-047QT,...
Keep your floors looking fabulous with this high-grade floor resin 4700 kit designed by Florock.This is an excellent floor resin...
Florock Florothane MC/HT - .75 Gal
$176.00
Florothane MC/HT Florothane MC/HT is a unique light stable urethane topcoat system that can be installed as either a high gloss or satin finish. It provides superior hardness andåÊexceptional abrasion resistance, resists manyåÊchemicals and solvents, and providesåÊa no-wax floor that is easy and economical to maintain. Florothane MC/HT is conveniently field-tintable with FloroTint Colorants. åÊ Colors åÊ Architectural Specs Florothane MC/HT Technical Data Florothane MC/HT High Gloss and Satin Urethane FloroTint Colorants
Florothane MC/HT Florothane MC/HT is a unique light stable urethane topcoat system that can be installed as either a high...
Florock Floor Resin 4805 Kit - Epoxy Clear - U0-161KT - 4Gal
$258.00
To protect your floors and keep them looking great, apply this floor resin 4700 kit by Florock.This is an excellent floor resin 4700 kit for concrete because of the epoxy resin and 100% solid base.It comes in clear, size 4 gal. A gloss finish looks great and makes for easy maintenance. Dry-time is 12 hr. after application. The application temperature is 55 degrees to 90 degrees F. It is designed for mild to moderate exposure conditions. Features Application Temperature: 55 to 90 Degrees F Exposure Conditions: Mild to moderate Size: 4 gal. Base Type: 100% Solid Finish: Gloss Features: Ideally Suited for Use As A Topcoat, Can Also Be Mixed with Ground or Fused Silica to Make An Epoxy Paste or Mortar Dry Time Tack Free: 8 hr. Dry Time - Light Traffic: 12 hr. Item: Floor Resin 4805 Kit For Use With: Mfr. No. M8-138QT, M1-067QT, M7-062QT, M4-056QT, M5-046QT,...
To protect your floors and keep them looking great, apply this floor resin 4700 kit by Florock.This is an excellent...
Vexcon - STARSEAL® PS CLEAR - 5GAL
$160.02 $177.80
StarSeal PS Clear STARSEAL PS CLEAR enhances the natural beauty of gray and decorative concrete surfaces and produces a wear-pattern free, shine retentive permanently sealed, low-maintenance densified concrete floor. StarSeal PS Clear is a high solids potassium based silicate that rapidly penetrates without scrubbing and rinsing. Simply apply, re-distribute and re-apply until the concrete no longer absorbs the material. Once absorbed, StarSeal PS Clear reacts with the calcium hydroxide in the concrete producing a stronger more durable, dust free, superior looking and performing long lasting concrete floor. BENEFITS Long lasting and extremely durable High solids forumation No scrubbing or rinsing required Eliminates or reduces waste stream during installation Odorless, non-hazardous, USDA approved Easy to clean LEED points Abrasion, wear resistant No topical film to wear through Performance warranty Low maintenance. No waxing or resurfacing required Brochure StarSeal PS Clear Safety Data Sheet StarSeal PS Clear
StarSeal PS Clear STARSEAL PS CLEAR enhances the natural beauty of gray and decorative concrete surfaces and produces a wear-pattern...
CONGELZ™ WASTE WATER HARDENER - 40lbs
$180.00 $200.00
Akona® Congelz™ Waste Water Hardener (BOM #107069) is the perfect method to dispose of unwanted rinse water from any cement or concrete project. Congelz patented technology is great for mortars, stuccos, grouts, patching products, and other similar materials. Using Congelz solves the issues caused by cementitious waste disposal - no more clogged drains or dumping of product on job sites. Simply add the product to your rinse water, allow to harden, and toss the works in the trash! Environmentally safe! Passes EPA 9095.   Printable Info TDS - Congelz SDS - Congelz FAQ - Congelz
Akona® Congelz™ Waste Water Hardener (BOM #107069) is the perfect method to dispose of unwanted rinse water from any cement...
Prime Shine Surface Honing Solution (SHS) 5GAL
$210.00
A surface honing solution with patented technology formula, allowing you to prepare the surface in conjunction with US Abrasives specially formulated grinding consumables by speeding up the process and ensuring the substrate is ready for polishing. With the use of a specific form of molecular nanotech, this science allows the product to penetrate deeper and helps enhance the hardening process, this is making it more defiant to surface abrasion. Providing extreme stock removal of all irregularities and leaving you fundamentally with a scratch free surface.   STORAGE AND HANDLING Store in a cool, dry place with adequate ventilation. Always seal container after dispensing. Do not alter or mix with other chemicals. Published shelf life assumes upright storage of factory-sealed containers in a dry place. Maintain temperature.  Keep from freezing. Do not double stack pallets. Dispose of unused product and container in accordance with local, state and federal regulations.   TYPICAL...
A surface honing solution with patented technology formula, allowing you to prepare the surface in conjunction with US Abrasives specially...
Prime Shine Densifier 5GAL
$225.00
PRIME SHINE DENSIFIER With innovative PATENTED technology, Prime Shine has a ability to provide a product that reacts and gives the positive aspects of sodium, potassium and lithium silicates. The revolutionary TRI-BOND Technology delivers a surface that forms a crystalline barrier within the pores to stop water, moisture, vapors and prevents dusting, heightening the resulting shine. A finished Prime Shine surface is breathable, but the transformed pore assembly prevents the passage of elements that cause efflorescence on the surface. Furthermore, it increases abrasion resistance, which increases the durability of the shine.   STORAGE AND HANDLING Store in a cool, dry place with adequate ventilation. Always seal container after dispensing. Do not alter or mix with other chemicals. Published shelf life assumes upright storage of factory-sealed containers in a dry place. Maintain temperature.  Keep from freezing. Do not double stack pallets. Dispose of unused product and container in accordance with local,...
PRIME SHINE DENSIFIER With innovative PATENTED technology, Prime Shine has a ability to provide a product that reacts and gives...
PRIME SHINE DEFENSE 5GAL
$329.00
Most hard surfaces are prone to foreign particles and contaminants. Natural stone have pores where dust particles and foreign spillage can seep right through. These particles can be detrimental to your hard surfaces structure as time goes on. This can result in staining, cracks and breaks. Prime Shine Defense is a penetrating product enhancing your surfaces life. This can prevent chemical damage and permanent staining by holding spills close to the surface. Prime Shine Defense is more resistant to organic materials while still allowing the surface to breathe. Prime Shine Defense is a non film forming product.      STORAGE AND HANDLING Store in a cool, dry place with adequate ventilation. Always seal container after dispensing. Do not alter or mix with other chemicals. Published shelf life assumes upright storage of factory-sealed containers in a dry place. Maintain temperature .  Keep from freezing. Do not double stack pallets. Dispose of...
Most hard surfaces are prone to foreign particles and contaminants. Natural stone have pores where dust particles and foreign spillage...
AMERIPOLISH SURELOCK DYE